 |
|
|
ETS-EB62-10BASET-MBNC-45-3C
Monoline Coax Balun - Male BNC to 3" UTP R45 Plug 10BaseT - 100 Ohm
Monoline Coax Balun - Male BNC to 3" UTP R45 Plug 10BaseT - 100 Ohm from ComputerCableStore™. The unique Monoline Baluns, only from ETS, allow you to reuse existing premise cabling for Ethernet 10BaseT networks. One run of Coax replaces two pair of UTP with improved NEXT (near end crosstalk) over the 802.3 specifica The BNC (Bayonet Neill Concelman) connector is a very common type of RF connector used for terminating coaxial cable. The BNC connector is used for RF signal connections, for analog and Serial Digital Interface video signals, amateur radio antenna connections, aviation electronics (avionics) and many other types of electronic test equipment. It is an alternative to the RCA connector when used for composite video on commercial video devices, although many consumer electronics devices with RCA jacks can be used with BNC-only commercial video equipment via a simple adapter. BNC connectors were commonly used on 10base2 thin Ethernet networks, both on cable interconnections and network cards, though these have largely been replaced by newer Ethernet devices whose wiring does not use coaxial cable. Some ARCNET networks use BNC-terminated coax.
Manufacturers > Energy Transformation Systems, Inc. > Ethernet Baluns & Panels > Monoline Coax Ethernet 10BaseT Baluns
|
ETS-EBS-10BASET-11-3-3C
Monoline Single Pair Balun - RJ11 3 cord pins 3 4 to RJ45 jack 10BaseT
Monoline Single Pair Balun - RJ11 3 cord pins 3 4 to RJ45 jack 10BaseT from ComputerCableStore™. The unique Monoline Baluns, only from ETS, allow you to reuse existing premise cabling the Ethernet 10BaseT networks. One single pair of UTP or STP replaces two pair UTP with improved NEXT (near end crosstalk) over the 802. The 8 Position 8 Contact (8P8C) (often called RJ45) plugs and sockets are most regularly used as an ethernet connector. 8P8C connectors are typically used to terminate twisted pair cable. RJ11 is a physical interface often used for terminating telephone wires. It is probably the most familiar of the registered jacks, being used for single line POTS telephone jacks in most homes across the world.Cables sold as RJ11 are nearly always 6P4C (six position, four conductor), with four wires running to a central junction box. Two of its six possible contact positions connect tip and ring and the other two conductors are then unused. 6P2C and 6P6C can also be found in stores.
Manufacturers > Energy Transformation Systems, Inc. > Ethernet Baluns & Panels > Pair Savers
|
ETS-PV935
VGA Passive Balun - Computer End for ETS-PV934
VGA Passive Balun - Computer End for ETS-PV934 from ComputerCableStore™. The ETS PV934 VGA Video Balun Set allows computer video signals that adhere to the VGA/SVGA/XVGA standards to be transmitted over Category 5 or better UTP wiring. All modes and resolutions operate normally. The term Video Graphics Array (VGA) refers specifically to the display hardware first introduced with the IBM PS/2 line of computers in 1987, but through its widespread adoption has also come to mean either an analog computer display standard, the 15-pin D-subminiature VGA connector or the 640×480 resolution itself. While this resolution has been superseded in the personal computer market, it is becoming a popular resolution on mobile devices.
Manufacturers > Energy Transformation Systems, Inc. > Multimedia > Video Baluns & Panels > Component Video Baluns
|
|
|
ETS-AV970
VGA & Stereo Audio/Video Balun Set - PV971 + PV973
VGA & Stereo Audio/Video Balun Set - PV971 + PV973 from ComputerCableStore™. The ETS PV970 VGA + Stereo Audio Balun Set allows computer video + stereo audio signals that adhere to the VGA/SVGA/XVGA standards to be transmitted over Category 5 or better UTP wiring. All modes and resolutions operate no The term Video Graphics Array (VGA) refers specifically to the display hardware first introduced with the IBM PS/2 line of computers in 1987, but through its widespread adoption has also come to mean either an analog computer display standard, the 15-pin D-subminiature VGA connector or the 640×480 resolution itself. While this resolution has been superseded in the personal computer market, it is becoming a popular resolution on mobile devices.
Manufacturers > Energy Transformation Systems, Inc. > Multimedia > Audio / Video Baluns & Panels
|
|
|
ETS-EB59-10BASET-MBNC-45-P
Monoline Coax Balun - Male BNC on 6"pigtail to RJ45 jack 10BaseT - 75 Ohm
Monoline Coax Balun - Male BNC on 6"pigtail to RJ45 jack 10BaseT - 75 Ohm from ComputerCableStore™. The unique Monoline Baluns, only from ETS, allow you to reuse existing premise cabling for Ethernet 10BaseT networks. One run of Coax replaces two pair of UTP with improved NEXT (near end crosstalk) over the 802.3 specifica The 8 Position 8 Contact (8P8C) (often called RJ45) plugs and sockets are most regularly used as an ethernet connector. 8P8C connectors are typically used to terminate twisted pair cable. The BNC (Bayonet Neill Concelman) connector is a very common type of RF connector used for terminating coaxial cable. The BNC connector is used for RF signal connections, for analog and Serial Digital Interface video signals, amateur radio antenna connections, aviation electronics (avionics) and many other types of electronic test equipment. It is an alternative to the RCA connector when used for composite video on commercial video devices, although many consumer electronics devices with RCA jacks can be used with BNC-only commercial video equipment via a simple adapter. BNC connectors were commonly used on 10base2 thin Ethernet networks, both on cable interconnections and network cards, though these have largely been replaced by newer Ethernet devices whose wiring does not use coaxial cable. Some ARCNET networks use BNC-terminated coax.
Manufacturers > Energy Transformation Systems, Inc. > Ethernet Baluns & Panels > Monoline Coax Ethernet 10BaseT Baluns
|
|
|
ETS-EB62-10BASET-FBNC-45-3C
Monoline Coax Balun - Female BNC to 3" UTP RJ45 Plug 10BaseT - 100 Ohm
Monoline Coax Balun - Female BNC to 3" UTP RJ45 Plug 10BaseT - 100 Ohm from ComputerCableStore™. The unique Monoline Baluns, only from ETS, allow you to reuse existing premise cabling for Ethernet 10BaseT networks. One run of Coax replaces two pair of UTP with improved NEXT (near end crosstalk) over the 802.3 specifica The 8 Position 8 Contact (8P8C) (often called RJ45) plugs and sockets are most regularly used as an ethernet connector. 8P8C connectors are typically used to terminate twisted pair cable. The BNC (Bayonet Neill Concelman) connector is a very common type of RF connector used for terminating coaxial cable. The BNC connector is used for RF signal connections, for analog and Serial Digital Interface video signals, amateur radio antenna connections, aviation electronics (avionics) and many other types of electronic test equipment. It is an alternative to the RCA connector when used for composite video on commercial video devices, although many consumer electronics devices with RCA jacks can be used with BNC-only commercial video equipment via a simple adapter. BNC connectors were commonly used on 10base2 thin Ethernet networks, both on cable interconnections and network cards, though these have largely been replaced by newer Ethernet devices whose wiring does not use coaxial cable. Some ARCNET networks use BNC-terminated coax.
Manufacturers > Energy Transformation Systems, Inc. > Ethernet Baluns & Panels > Monoline Coax Ethernet 10BaseT Baluns
|
| 1 2 3 4 5 6 7 8 9 10 ... Next > |
|
|